Replacement starter motor for 2006 on models. Also known as 97729R

This is a less expensive aftermarket replacement for the OE starter.
Not interchangeable with Valeo and Bosch starters from earlier models. Get a £20 discount on this part if you send us your faulty but reconditionable starter motor

 1 in stock

 05730730 GU05730730 05 73 07 30
 0573 0730 0573.0730 05.73.07.30

Rear stop switch

BRA01004 may be used as a less expensive alternative brake light switch

 1 in stock

 854973 MG854973

Rear stop switch

Rear brake light switch

 1 in stock

2D0002805

Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on

 This part is available by special order, request a quote

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Discontinued by Bosch, superceded to 97729R. Also see ELA05731 for new replacement part or ELC05730 for reconditioned alternative

 This part is available by special order, request a quote

 05730730 GU05730730 05 73 07 30
 0573 0730 0573.0730 05.73.07.30

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Silca key blank for ignition key, match profile to your existing key

 This part is due back in stock soon, call 01484 841395 to reserve yours

NE5

Silca key blank for ignition key, match profile to your existing key

 This part is due back in stock soon, call 01484 841395 to reserve yours